Jewelry and Metalcraft
Revision as of 17:10, 3 August 2016 by Lynne.Davis (talk | contribs) (→Metals 100: Introduction to the Jewelry and Metal Crafts Shop)
Contents
- 1 Equipment List
- 1.1 Hand Tools
- 1.2 Bench Tools
- 1.3 Soldering station
- 1.4 Patina setup
- 1.5 Electro-etch setup
- 1.6 Firing Setup
- 1.7 Enameling Setup (On Loan to TinkerMill)
- 1.8 Casting
- 1.9 Lapidary (On Loan to TinkerMill)
- 1.10 Lathe (On Loan to TinkerMill)
- 1.11 Hydraulic Press
- 1.12 Rolling Mill
- 1.13 Shear
- 1.14 Bending brake
- 2 Classes
- 2.1 Curriculum Map
- 2.2 Metals 100: Introduction to the Jewelry and Metal Crafts Shop
- 2.3 Metals 101: Basic Hand Tools & Fabrication
- 2.4 Metals 102: Power Tools & Uses
- 2.5 Metals 200: Introduction to Torch use: Theory and Practice
- 2.6 Metals 201: Torch use - Single fuel
- 2.7 Metals 202: Torch use - Dual fuel
- 2.8 Metals 203: Torch use - Molten metal
- 2.9 Metals 300: Introduction to Chemical and Electrolytic Surface Treatments
- 2.10 Metals 301: Electrolytic Etching
- 2.11 Metals 302: Applying Chemical Patinas and Inks
- 2.12 Metals 303: Annodizing
- 2.13 Metals 400: Introduction to Kiln Use
- 2.14 Metals 401: Using the Metal Craft Shop Kiln
- 2.15 Metals 500: Introduction to Lapidary Use
- 2.16 Metals 501: Using the Lapidary for Stone Shaping
- 2.17 Metals 600: Intro to Lathes at TinkerMill
- 2.18 Metals 601: Using the Small Metal Lathe
- 3 References and Resources
Equipment List
Hand Tools
- Hammers-assorted
- Pliers-assorted
- Files-assorted
- Files-assorted needle
- Sanding sticks
- Jeweler's saw (x2)
- Calipers
- Hand shears, tin snips - assorted
- Hole punch (Prat and Whitney)
- Bench blocks
Bench Tools
- Flex Shaft w/assorted bits
- Dremel w/drill press stand
- Bench pins
- Small vice/bench block (x2)
- Large vice
- Large anvil
- Belt sander
- Bench grinder/wire wheel
- Dapping block and punches
Soldering station
- Butane torch
- Oxygen/Acetylene torch
- MAPP gas torch
- Pickle pot, chemical
- Tongs, tweezers
- Rinse pot
- Cleaning supplies
Patina setup
- Glass mixing jars and dishes
- Brushes/applicators
- Chemicals
- Steel wool
Electro-etch setup
- DC Power supply
- "D" battery holders
- Battery clips
- Etching vessels
- Resist materials
- Chemicals
Firing Setup
- Kiln (On Loan to TinkerMill)
- Programmable controller
Enameling Setup (On Loan to TinkerMill)
- Sifting screens
- Enamel powders
- Enamel holding agent (e.g. Kleerfire)
- Kiln trivets, wire screen
Casting
- Centrifugal rig (On Loan to TinkerMill)
- Sand casting kit with casting frame, crucible, release agent, pre-mixed casting sand, tongs
Lapidary (On Loan to TinkerMill)
- Trim saw, cab forming wheels (Lortone LU6X Combination Unit) refurbished
Lathe (On Loan to TinkerMill)
Hydraulic Press
- (to be converted from battery casing press to custom forming tool)
Rolling Mill
- Small Pepe
- Part of 3-in-One
Shear
- Part of 3-in-1
Bending brake
- Part of 3-in-1
- Stand-alone brake (larger than 3-in-1)
Classes
Curriculum Map
See [Map]
Map is still under development.
Metals 100: Introduction to the Jewelry and Metal Crafts Shop
[Get Handout|Handout_Metals_100.pdf]
- Prerequisite: none
- Certification: no
- Duration: 60 minutes
- Prerequisite for: All certificate classes
Metals 100 is a comprehensive introduction to the Jewelry and Metal Craft shop within TinkerMill.
It is a non-certificate class but is a prerequisite for any shop certification class.
It introduces the shop's tool groups, safety and guidelines, self-study resources,
and examples of the types of projects best suited to this shop.
Metals 100 covers:
- Safety first
- Shop rules, (Ferrous vs Nonferr.) priority use, scale matters
- Tool groups in the shop
- Overview of curriculum paths and classes to become certified for independent tool use
- Resources for independent study and collaboration: books, magazines, shop web portal, TM experts, organizations, and suitable project suggestions
Metals 101: Basic Hand Tools & Fabrication
- Prerequisite: Metals 100
- Certification: Metals 101 - Hand tools
- Duration: 1.5 - 2 hours
- Required for: Metals 102 (Power tools) and Metals 201 (Single Fuel Torch) and specified project classes
Metals 101 is a certification class for independent use of the shop's basic hand tools. It provides:
- Instruction on the safe and appropriate use of unpowered hand tools
- List of tools included in this certification
- Additional self-study references and list of resources: e.g.: Wire+Metals Text, Web
- Time in class or at Open Studio times to practice using the tools and complete the sampler project required for certification
- Certification sampler project: Described in class handout
Tools certified:
- Jeweler’s saw
- Hole punch
- Files
- Sanding media
- Hammers
- Ring mandrel, bench block, anvil
- Dapping punch
- Disc cutter
- Pliers
- Aviation shear
- Calipers, Wire gauge, Jewelers’ rule
- Bench pin
- Stamps and punches
- Jumpring maker
Metals 102: Power Tools & Uses
- Prerequisite: Metals 100
- Certification: Metals 102 - Power tools
- Duration: 2 hours
- Required for: Specified project classes
Metals 102 is a certification class for independent use of the shop's listed power tools. It provides:
- Instruction on the safe and appropriate use of shop's power tools
- List of tools included in this certification
- Additional self-study references and list of resources: e.g.: Wire+Metals Text, Web
- Time in class or at Open Studio times to practice using the tools and complete the sampler project required for certification
- Certification sampler project: Described in class handout
Tools certified:
- Dremel Drill press
- Foredom Flexshaft
- Bench Buffer
- Belt Sander
Metals 200: Introduction to Torch use: Theory and Practice
- Prerequisite: Metals 100 and 101
- Certification: none
- Duration: 60 minutes
- Required for: Metals 201 (Single Fuel Torches)
The Metals 200 is a non-certificate class to introduce the use of the shop's torches to anneal, join or fuse metal. You will hear about the certificate classes offered, and learn when you can use the torches independently at TinkerMill. This class demonstrates the differences between soldering, brazing, and welding, annealing and tempering metal. It also provides a bit of theory and terminology for this practice.
Metals 200 covers:
- Safety first
- Soldering station equipment, supplies, and conventions
- Torch-related certifications
- Single fuel vs dual fuel uses
- Flame heat principles
- Understanding annealing
- Demonstrations
- Examples
- Q&A
- Resources: books, magazines, web, TM experts, organizations, and project suggestions
- List of tools included in certifications
Metals 201: Torch use - Single fuel
- Prerequisite: Metals 200
- Certification: Metals 201 - Single Fuel Torches and tools requiring annealed materials
- Duration: 90-120 minutes
- Required for: Metals 202 and specified project classes
This class is a certification class for independent use of the shop's single fuel torches (Butane, Propane, MAPP Gas, Acetylene-Air).
It provides:
- Theory: Annealing different metals, silver soldering
- Instruction on the safe and appropriate use of torches for basic jewelry-making (annealing and silver soldering)
- Instruction to use tools that may be used only with annealed metal
- List of tools and techniques requiring annealing (e.g.: texturing, raising, folding, riveting, making headpins)
- Reference materials
- Additional self-study resources
- Hands-on trials (supervised)
- Open Studio time to practice using the tools safely and complete the sampler project required for certification
- Certification sampler project: Described in class handout
Tools certified:
- Butane torch
- Acetylene/AIR torch (not Oxygen/Acetylene torch)
- MAPP Gas torch
- Soldering station - materials and tools (solder, pickle, quench, hand tools, etc.)
- Rolling mill
- 3-in-1, bending brake
- Review of dapping block and disc cutter, use of punches
Metals 202: Torch use - Dual fuel
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 203: Torch use - Molten metal
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 300: Introduction to Chemical and Electrolytic Surface Treatments
- Prerequisite: none
- Certification: no
- Duration: 30 minutes
- Required for: Metals 301 (Electrolytic Etching), Metals 302 (Chemical Patinas and Inks), Metals 303 (Annodizing)
Metals 300 is a non-certificate class to introduce the use of the shop's equipment to alter the surface appearance of metal using an electrical charge and/or chemical means. You will hear about the certificate classes offered which allow you to use this equipment independently at TinkerMill. This class explains and gives some examples of the differences between these surface treatment methods. It also provides a bit of theory and terminology for this practice.
Metals 300 covers:
- Safety first
- Station equipment, supplies, and conventions
- Certifications
- Storage and disposal of chemicals at TinkerMill
- Demonstrations
- Examples
- Q&A
- Resources: books, magazines, web, TM experts, organizations, and project suggestions
- List of tools included in certifications
Metals 301: Electrolytic Etching
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 302: Applying Chemical Patinas and Inks
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 303: Annodizing
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 400: Introduction to Kiln Use
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 401: Using the Metal Craft Shop Kiln
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 500: Introduction to Lapidary Use
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 501: Using the Lapidary for Stone Shaping
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 600: Intro to Lathes at TinkerMill
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
Metals 601: Using the Small Metal Lathe
- Prerequisite:
- Certification:
- Duration:
- Required for:
Description
References and Resources
- Bookmarks - resources edited.pdf Contains a few hundred bookmarked resources Lynne Davis has accumulated over several years. As is - no warranty!
- Lapidary Forum This is an extremely comprehensive and authoritative site for jewelry makers.
- Buffing and Polishing Guide from Sharr Choate's book, Chapter 8: Creative Gold and Silversmithing
