Difference between revisions of "Laser Cutter Settings"
Jump to navigation
Jump to search
Mjporter86 (talk | contribs) |
Mjporter86 (talk | contribs) |
||
| Line 9: | Line 9: | ||
!Passes | !Passes | ||
!Notes | !Notes | ||
| + | |- | ||
| + | |Basswood ||1/18" ||15 ||40 || 1 || | ||
| + | |- | ||
| + | |Basswood ||1/16" ||25 ||40 || 1 || | ||
| + | |- | ||
| + | |Birch Plywood ||3mm (1/8") ||15 ||70 || 1 ||It is EXTREMELY likely you can cut this at lower power. | ||
| + | |- | ||
| + | |Oak ||1/4" ||12 ||30 || 1 || | ||
| + | |- | ||
| + | |White Ash Plywood ||1/4" ||100 ||40 ||1 || | ||
|} | |} | ||
| Line 19: | Line 29: | ||
!Passes | !Passes | ||
!Notes | !Notes | ||
| + | |- | ||
| + | |Acrylic ||1/8" ||15 ||55 ||1 || | ||
| + | |- | ||
| + | |Delrin (White) ||1/4" ||12 ||70 ||2 ||Delrin contains plenty of formaldehyde. Allow extra time after cutting for the cutter to vent. | ||
|} | |} | ||
| Line 39: | Line 53: | ||
!Passes | !Passes | ||
!Notes | !Notes | ||
| + | |- | ||
| + | |Leather (Veg Tan) ||Approx 1/8" ||50 ||50 ||1 ||Cut edges will char, which can be brushed away with a stiff brush. The char also can be polished for a shiny finished edge. | ||
|} | |} | ||
Revision as of 16:31, 3 June 2017
Contents
General Cutting Settings
These settings are for general purpose use to cut materials. They should be expected to fully cut the material, but ALWAYS test settings to verify they work with your specific material!
Woods
| Material | Thickness | Speed | Power | Passes | Notes |
|---|---|---|---|---|---|
| Basswood | 1/18" | 15 | 40 | 1 | |
| Basswood | 1/16" | 25 | 40 | 1 | |
| Birch Plywood | 3mm (1/8") | 15 | 70 | 1 | It is EXTREMELY likely you can cut this at lower power. |
| Oak | 1/4" | 12 | 30 | 1 | |
| White Ash Plywood | 1/4" | 100 | 40 | 1 |
Polymers
| Material | Thickness | Speed | Power | Passes | Notes |
|---|---|---|---|---|---|
| Acrylic | 1/8" | 15 | 55 | 1 | |
| Delrin (White) | 1/4" | 12 | 70 | 2 | Delrin contains plenty of formaldehyde. Allow extra time after cutting for the cutter to vent. |
Paper Materials
| Material | Thickness | Speed | Power | Passes | Notes |
|---|
Miscellaneous
| Material | Thickness | Speed | Power | Passes | Notes |
|---|---|---|---|---|---|
| Leather (Veg Tan) | Approx 1/8" | 50 | 50 | 1 | Cut edges will char, which can be brushed away with a stiff brush. The char also can be polished for a shiny finished edge. |
General Engraving Settings
The settings here are for general-purpose use and are NOT calibrated for depth! ALWAYS test settings to verify them!
Woods
| Material | Thickness | Speed | Power | Passes | Notes |
|---|
Polymers
| Material | Thickness | Speed | Power | Passes | Notes |
|---|
Paper Materials
| Material | Thickness | Speed | Power | Passes | Notes |
|---|
Miscellaneous
| Material | Thickness | Speed | Power | Passes | Notes |
|---|
Detailed Settings
Below are in-depth engraving tests that have been contributed by various members. Unlike the general purpose settings, these settings include the approximate depth to which the engraving will be cut, which may be useful for things such as stamps.
Back to: Main Page
