Lampwork

From TinkerMill Wiki
Revision as of 17:49, 19 July 2016 by Admin (talk | contribs) (Created page with "===== Tools ===== * '''Bench Burner''' - A torch that is fixed to the bench which provides a stationary flame. * '''Didymium Safety Glasses''' - Glasses that provide a filter...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
Tools
  • Bench Burner - A torch that is fixed to the bench which provides a stationary flame.
  • Didymium Safety Glasses - Glasses that provide a filter which selectively blocks the yellowish light at 589 nm emitted by the hot sodium in the glass, without having a detrimental effect on general vision, unlike dark welder's glasses. The strong infrared light emitted by the super-heated forge gases and insulation lining the forge walls is also blocked thereby saving the lampworker's eyes from serious cumulative damage.
  • Hand Torch - The hand torch allows for more maneuverability of the flame, commonly used on glassworking lathes where there is reduced maneuverability of the piece
  • Kiln - the kiln is used to garage and anneal the glass, protecting the piece from thermal shock and relieving thermal stress.
  • Marver - flat surfaces used to roll glass upon in order to shape, smooth or consolidate applied decoration, typically made of graphite or steel.
  • Paddle - A graphite or metal marver attached to a handle
  • Reamer - A piece of graphite or brass on a handle used to enlarge holes.
  • Blowhose/Swivel Assembly - A hose, usually latex, is connected to the blowpipe via a hollow swivel, allowing the lampworker to blow into hollow glass forms while rotating them.
  • Tungsten Pick - The extreme temperature resistance of tungsten makes it ideal for raking(dragging glass around on the surface), or to bore a hole through the glass.
  • Shears - Steel shears are used to cut the hot glass.
  • Hot Fingers - Metal tool found in various configurations which allows the hot glass to be securely held and rotated, commonly used for finishing pieces after they have been removed from the blowpipe or pontil.
  • Pontil (Punty) - A small diameter glass rod used to hold a piece while working on it. The end of the punty is heated, melted, and then secured to the work piece. Later, the cold joint connecting the work piece and the punty can be broken with a light tap on a solid surface. It often leaves an irregular or ring-shaped scar on the base when removed called the "pontil mark".
Terms
  • Flame Cutting - A technique for separating a section of glass into two pieces. The area to be separated is held in the flame until until it is a bright honey color. The sections are then pulled apart while remaining in the flame, resulting in a very thin strand of glass between the two that is quickly cut and balled up by the flame.
Operating the Bench Burner
Start Up
  1. Ensure that the oxygen tank regulator valve is loose.
  2. Ensure that the oxygen valve on the bench burner (silver knob) is closed.
  3. Turn on the oxygen tank.
  4. Adjust the oxygen pressure to 40 psi by turning the regulator valve clockwise.
  5. Ensure that the propane valve on the bench burner (red knob) is closed.
  6. Turn on the propane tank.
  7. Check that the propane tank regulator is set to 5 psi, adjust if necessary.
  8. Using a hand held lighter, hold a flame in front of the torch nozzle.
  9. Slowly turn the bench burner's propane valve (red knob), this will start the flow of propane gas from the end of the torch which the lighter will ignite.
  10. Slowly turn on the bench burner's oxygen valve and adjust the flame until the cones (smaller, blue flames within the base of the larger flame) are sharp and defined.
Shut Down
  1. Turn off the oxygen tank valve.
  2. Bleed the oxygen from the torch hose by loosing the silver knob on the torch's base. Wait a few seconds for the gas the escape.
  3. Close the torch's silver oxygen valve (take care to not over tighten!)
  4. Turn the oxygen regulator valve counter clockwise until it is loose.
  5. Turn off the propane tank valve (do not adjust the regulator.)
Material Resources
  • Glass Craft, 411 Violet Street Golden, CO www.glasscraftinc.com
  • D&L Art Glass Supply, 1440 W. 52nd Ave. Denver, CO www.dlartglass.com